Concrete cutting in Riverside CA - straight cuts with the dust kept down
Need a trench, a driveway section out or an opening in a concrete wall? We make clean, wet cuts right where you need them.
- Licensed and insured.
- Free estimates at your property.
- Replies within 1 business day.
How does concrete cutting work on a Riverside slab or wall?
Concrete cutting in Riverside means sawing a slab or wall along a marked line, so a trench, a damaged section or a new opening comes out clean and the concrete around it stays whole and usable.
Most calls start with something that has to get through concrete, like a plumber who needs a trench across a garage floor, a cracked driveway panel that has to come out, or a doorway you want in a concrete wall. The price moves with whether it's a floor or a wall, how long and deep the cut runs, whether there's rebar running through the slab to hold it together, whether the work is indoors and whether you want the pieces hauled off. The schedule mostly turns on getting buried lines marked and settling the permit question before the saw starts, and my written estimate spells out what's included so you see your own figure.
How we handle concrete cutting
Before anything gets cut, I ask whether it's a floor or a wall and whether you want the cut pieces hauled off, because those two answers decide which saw we bring and what the estimate covers. On cutting day we snap the lines where we agreed, then cut wet so the dust stays down, and we catch the slurry, the gray water and grit the blade throws off, so it doesn't end up in the street drains. If removal is part of the job, we lift the panels out, load them up and leave the area swept, and if it isn't, the cut pieces stay in place for whoever comes next.
Cutting is often the first half of a bigger job. A cracked or sunken panel cut out of a driveway can be poured back as part of our concrete driveway building work, and an old slab cut up and hauled off clears the way for concrete patio construction. When we pour back, we dig out and pack the subgrade, what the new concrete sits on, before anything else, because that's the part nobody sees and the part that decides whether the new piece settles.
Flat sawing for slabs and trenches
This is the saw that rolls across the top of horizontal concrete, so it handles floors, driveways, sidewalks and trench cuts. It suits most homeowner jobs, from a plumbing trench to pulling out one bad section of driveway.
Wall sawing for openings
A wall saw is a diamond saw that runs along a rail fixed to the wall, so it can cut walls, columns and openings where a floor saw can't work. If you want a new doorway or window in a concrete wall, this is the method that fits.
If a plumber or electrician is waiting on a trench, call (951) 589-3080 early, because buried lines have to be marked before we cut anything.
What happens after you call about concrete cutting in Riverside?
I do the estimate myself and run our crew on cutting day, so the person who measured your slab or wall is the one standing there when the saw starts. Here's how it goes.
Tell us about the cut
Call (951) 589-3080 or send the form with where each cut goes, whether it's a slab or a wall, a rough length in linear feet, indoors or out, and whether you want the pieces hauled off. That's enough for me to plan the visit.
I measure and write it up
I come out, look at the slab or wall, ask what the trench or opening is for and leave a written estimate that says what's in it. You'll see whether removal and cleanup are covered, so there's no guessing about the total.
Cut, clean up and walk through
Once you say go, we check what the city wants, get buried lines marked, then cut, clean up and walk the finished job with you. If a permit is needed, we pull it ourselves or help you apply.
Get a written estimate for your concrete cut
Send the form and we'll reply within one business day to set a time. I'll come out, measure and leave a free written estimate at your property, and there's no obligation to go ahead.
(951) 589-3080Concrete cutting in Riverside and where the water goes
Cutting wet matters twice on a Riverside job. Dry concrete dust carries crystalline silica, which can cause lung cancer, kidney disease and silicosis, a lung disease with no cure that's often fatal, so California's workplace silica rule lists walk-behind saws with a built-in water feed that keeps the blade wet the whole time it runs. How a crew handles dust is a fair thing to ask any cutter you're comparing. The water is the other half of it, because the City of Riverside says whatever washes into the streets and storm drains flows untreated into local streams and rivers, so we catch the slurry from every cut instead of letting it run down the gutter.
Around here most of our cutting is on driveways, garage slabs and patios, either trenches for new lines or sections pulled out where roots or settling cracked them, and it's the same work we do in Jurupa Valley and Moreno Valley. We're based in Riverside and work in many of the cities around it in Riverside and San Bernardino counties, so if your city isn't listed, call and ask.
Concrete cutting questions from Riverside homeowners
How much does concrete cutting cost in Riverside?
Professional saw cutting of concrete slabs usually runs about $4 to $15 per linear foot across the US, and that covers the sawing, not hauling the pieces away. Reinforced or deeper slabs commonly cost more per foot, and on a short cut the charge for bringing the saw and crew out can matter more than the per-foot rate. I'll measure yours and put the number in writing.
Does the price of concrete cutting include removing the concrete?
Not always, because sawing and removal are separate jobs, and a cutter may make the perimeter or trench cuts and leave the panels where they sit. When you compare quotes, ask each one whether hauling off the cut pieces is part of the price. Ours says so plainly either way.
Who calls to locate buried utilities before concrete is cut?
An industry sample specification for slab sawing puts that call on the owner or whoever is contracting the work, made to the right agency as state or local rules require. That's why it's worth deciding who makes the call well before cutting day, and I go over it with you at the estimate so the lines are marked before the saw starts.
How do I know what's inside a slab before it gets cut?
A ground-penetrating radar scan, which looks inside the concrete with radar, can help, but a blank scan only means nothing was located, not that nothing's there. One scanning guide from Australia advises cutting only in areas the scan operator has declared clear of hidden objects.
What license covers concrete sawing in California?
The state's contractors license board lists concrete sawing, breaking and coring under its concrete related services classification. Ask any cutter you're comparing what license they carry. We're licensed and insured.
What is the best way to cut concrete inside a house or garage?
Plan for more setup than an outdoor cut, because the crew needs to manage the water, recover the slurry and add ventilation, barriers or dust extraction around the work. That extra setup is why indoor cutting may cost more than the same cut on a driveway. Tell us it's indoors when you call so I can look at the room and how we'll get the saw in.
Concrete work that often follows a cut
Pulled a broken panel out of your driveway, or want the whole thing redone? We rebuild driveways from the ground up, starting with what the slab sits on.
If a cut opens up space in the backyard, or the old slab never drained right, a new patio poured on a packed base can handle both.
Tell us where the cut goes
Call (951) 589-3080 any day until 11 PM, or send the form, and I'll set a time to come look at your slab or wall.